Kobalt KT1015 Table saw dust port to Rigid Shop vac adapter
thingiverse
... of tools. ...but I believe shop vac hoses are pretty standard at 1.75". The dustport on the table saw is a little strange at 2.55" I printed it with solid infill but I'm sure it'd be fine otherwise. ...It's a bit thicker than most adapters at .095"
Kobalt table saw height adjuster
prusaprinters
Kobalt table saw height adjuster. Lowes doesn't sell replacement crank handles. ...Created with Tinkercad in 2018.</p>
Kobalt Table Saw Dust Collection
thingiverse
Adapter for the Kobalt Table Saw to go from the standard port on the bottom to connect to 2" PVC fittings or 2.5" dust collection hose.
T-track bracket for Kobalt table saw
thingiverse
This is a T-track bracket that fits a Kobalt table saw. Could be used to make a miter sled or a better fitting miter gauge. ...
Dust Adapter for Hitachi Miter Saw and Kobalt Table Saw
thingiverse
Dust Adapter for Hitachi Miter Saw and Kobalt Table Saw to fit a Shopvac hose
Dust Adapter for Hitachi Miter Saw and Kobalt Table Saw
prusaprinters
Dust Adapter for Hitachi Miter Saw and Kobalt Table Saw to fit a Shopvac hose Category: 3D Printing
Vacuum Adapter, Kobalt Table Saw to Rigid Vac
thingiverse
I wanted an adapter for my Rigid Shop Vac to my Kobalt Table Saw and my Mini Hose for my sander/skill saw.
Kobalt XTR Reciprocating Saw
sketchfab
3D scan using Artec Spider of new Kobalt XTR Reciprocating Saw (without battery).
Kobalt Circular Saw Vacuum Adapter
thingiverse
This is a vacuum adapter for the Kobalt 24V Max circular saw (KCS 6524B-03). Simply remove the back-most screw in the blade housing, slide the vacuum adapter in, put the screw back. It is designed to work at all bevel angles. The OD is 1.5" and the...
Kobalt Miter saw Dust Channel
thingiverse
Used for better duct collection on a Kobal 12" miter saw. ...Available in shot and long version. Photos are the short version. I used double sided sticky tape to attach it to the saw, even though it is a snug fit.
Kobalt Router Table Ring
thingiverse
Kobalt Router Table Ring was a replacement for the missing piece of my router table. ...You may have to do some fine tuning for this item to fix snuggly in.
Kobalt Router Table Inserts
thingiverse
Replacement router table inserts for the Kobalt Router Table. They fit better than the originals. About one hour print time per insert. Printed at .2 layer height and 50% fill. Center hole sizes match the OEM inserts:Small 1-1/4" center hole...
Kobalt miter saw blade guarded bushing
thingiverse
Kobalt miter saw blade guarded bushing part number os1s
Kobalt 24v Miter Saw Zero Tolerance
thingiverse
I needed a zero tolerance insert for my kobalt 24v miter saw. ...designed in sketchup with .skp included for any modifications.
Kobalt mitre saw stand extension bracket
thingiverse
This is the end plastic piece of a Kobalt brand mitre saw stand. The ends on those are made of plastic and break super easily if the support extension is... extended. This was tight when put on and printed at 100% in PLA, so you might want to...
Kobalt Miter Saw (0857242) dust shoud
cults3d
Dust collection for Kobalt 12 inch Miter saw. Uses 4 of the magnets listed below, but honestly friction fits into place perfectly fine without them. There are 2 2-1/2 inch ports, but 1 is honestly sufficient if you're just using a shopvac; if...
Kobalt Miter Saw (0857242) dust shoud
thingiverse
Dust collection for Kobalt 12 inch Miter saw. Uses 4 of the magnets listed below, but honestly friction fits into place perfectly fine without them. There are 2 2-1/2 inch ports, but 1 is honestly sufficient if you're just using a shopvac; if...
Kobalt Router Table Push Block
thingiverse
Push block for the Kobalt router table. The included push block was quite loose in the track and this is a nice tight fit (on mine at least). ...I also made a positive and negative 15 degree block since I seem to use those angles quite a bit in...
Kobalt Router Table Tool Holder
thingiverse
This is a first attempt at making a tool holder for the Kobalt Router table. It is printed in two parts to avoid using supports. The pieces will be bonded with glue. This holds two inserts, the 1/2" collet, the starting pin, wrench, and lift allen...
Kobalt table saw height adj handle UPDATED for better printing
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/hFq4fngbUt9
Table Saw
grabcad
3 HP Table Saw for cutting lumber
Table saw
cults3d
Support de fermeture pour table de découpe. ... Support for guide Table Saw
Table saw
thingiverse
Support de fermeture pour table de découpe. ... ------------------------------------------------------------ Support for guide Table Saw
Table Saw
thingiverse
This is a Table Saw which was designed out of spare Parts
Kobalt saw 58mm to 40.5mm shop vac adapter
thingiverse
Shop Vac to Kobalt compound miter saw. I make this for a friend. It would be better with a right angle in it but works fine as is.Customized version of http://www.thingiverse.com/thing:969819Created with Customizer!
Saw Table
thingiverse
This is a simple saw table for use with a jewelers saw or any hand tools that require a supported workpiece. ...Easily scaled.
Kobalt Miter Saw Lock Handle - Need Help Finishing!
thingiverse
I have the Kobalt 12" Compound Miter Saw, that tilts both directions. This is the locking handle for the tilt part of the saw. This handle is right next to the handle that locks the miter plate. THIS handle lifts up. The other handle pushes down....
Table saw
grabcad
This table saw features a height-adjustable top, enabling easy operation through an ingenious angular gear system.
TABLE SAW
grabcad
Create Your Own Table Saw at Home Writing your own table saw is an exciting DIY project that can save you money and give you the satisfaction of creating something yourself. With some basic tools, materials, and instructions, you can build a...
Table Saw
grabcad
A design is devised for an expansive table saw within the workshop, which incorporates the motor components sourced from Ryobi's BTS15 assembly.
